Workshop Technology

Q1: Thread rolling is restricted to

A ferrous materials

B ductile materials

C hard materials

D none of these

Q2: Metal patterns are used for

A small castings

B large castings

C complicated castings

D large scale production of castings

Q3: The electrodes used in spot welding have a tip of

A stainless steel

B aluminium

C copper

D brass

Q4: The chisel used for cutting key ways is

A flat chisel

B cape chisel

C round nose chisel

D diamond pointed chisel

Q5: The tolerance produced by shell moulding process of casting is

A +0.05 mm

B ±0.2 mm

C +0.5 mm

D ±1 mm

Q6: A zinc diffusion process is called

A galvanising

B anodising

C parkerising

D sherardizing

Q7: The algebraic difference between the minimum limit and the basic size is called

A actual deviation

B upper deviation

C lower deviation

D fundamental deviation

Q8: Galvanising is a

A zinc diffusion process

B process of coating zinc by hot dipping

C process used for making thin phosphate coating on steel

D none of the above

Q9: Which of the following welding process uses non-consumable electrodes?

A TIG welding

B MIG welding

C Manual arc welding

D Submerged arc welding

Q10: Which of the following methods can be used for manufacturing 2 metre long seamless metallic tubes?

A Drawing

B Extrusion

C Rolling

D Extrusion and rolling

Q11: In a four high rolling mill, there are four rolls out of which

A one is working roll and three are backing up rolls

B two are working rolls and two are backing up rolls

C three are working rolls and one is backing up roll

D all of the four are working rolls

Q12: Surface plate is used to check the trueness of flat surfaces.

A True

B False

Q13: In welding copper alloys with TIG arc welding

A direct current with straight polarity is used

B direct current with reversed polarity is used

C alternating current is used

D any one of these

Q14: In average work, the tolerance produced by investment casting method is

A ±0.05 mm

B +0.2 mm

C +05 mm

D +1 mm

Q15: In sheet metal blanking, shear is provided on punches and dies so that

A press load is reduced

B good cut edge is obtained

C warping of sheet is minimised

D cut blanks are straight

Q16: A taper provided on the pattern for its easy and clean withdrawl from the mould is known as

A machining allowance

B draft allowance

C shrinkage allowance

D distortion allowance

Q17: The blank diameter used in thread rolling will be

A equal to minor diameter of the thread

B equal to pitch diameter of the thread

C a little larger than the minor diameter of the thread

D a little larger than the pitch diameter of the thread

Q18: The purpose of a riser is to

A deliver molten metal into the mould cavity

B act as a reservoir for the molten metal

C feed the molten metal to the casting in order to compensate for the shrinkage

D deliver the molten metal from pouring basin to gate

Q19: The property of sand due to which it evolves a great amount of steam and other gases is called

A collapsibility

B permeability

C cohesiveness

D adhesiveness

Q20: A plug gauge is used to check the diameter of shafts and studs.

A Correct

B Incorrect

Q21: The temperature at which the new grains are formed in the metal is called

A lower critical temperature

B upper critical temperature

C eutectic temperature

D recrystallisation temperature

Q22: A saw which cuts wood during the return stroke of the saw is known as

A push saw

B pull saw or draw saw

Q23: The fullers are used

A for finishing flat surfaces

B for necking down a piece of work

C for punching a hole

D to finish the punched hole

Q24: The low pressure acetylene is produced at the welding site by the chemical reaction between water and calcium carbonate.

A Correct

B Incorrect

Q25: In __________ welding, the weld may be made either from left to right or from right to left.

A fore-hand

B back-hand

C vertical

Q26: In back-hand welding, the angle between the welding torch and the work is kept as

A 30°-40°

B 40°-50°

C 50°-60°

D 60°-70°

Q27: In a centrifugal casting method

A core is made of sand

B core is made of ferrous metal

C core is made of non-ferrous metal

D no core is used

Q28: In arc welding, the electric arc is produced between the work and the electrode by

A voltage

B flow of current

C contact resistance

D all of these

Q29: In a hot chamber die casting machine

A melting pot is separate from the machine

B melting pot is an integral part of the machine

C melting pot may have any location

D high temperature and pressure is used

Q30: In a bilateral system of tolerance, the tolerance is allowed on

A one side of the actual size

B one side of the nominal size

C both sides of the actual size

D both sides of the nominal size

Q31: When a pattern is made in three parts, the bottom part is known as a cope.

A True

B False

Q32: A pattern maker's shrinkage rule considers

A all pattern allowances

B only shrinkage allowance

C all materials to be cast

D all materials of the pattern

Q33: In submerged arc welding, an arc is produced between a

A carbon electrode and the work

B metal electrode and the work

C bare metal electrode and the work

D two tungsten electrodes and the work

Q34: The instrument which has all the features of try-square, bevel protractor, rule and scriber, is

A outside micrometer

B inside micrometer

C depth gauge micrometer

D combination set

Q35: The bloom is smaller than a billet.

A True

B False

Q36: The accuracy of micrometers, calipers, dial indicators can be checked by a

A feeler gauge

B slip gauge

C ring gauge

D plug gauge

Q37: The machining allowance provided on patterns depends upon

A type of casting metal

B size and shape of casting

C method of casting used

D all of these

Q38: The ferrous metals require more machining allowance than non-ferrous metals.

A True

B False

Q39: The cold chisels are made by

A drawing

B rolling

C piercing

D forging

Q40: The draft or taper allowance on casting is generally

A 1 to 2 mm/m

B 2 to 5 mm/m

C 5 to 10 mm/m

D 10 to 15 mm/m

Q41: The cross-section of a chisel is usually

A rectangular

B square

C hexagonal

D octagonal

Q42: In shielded arc welding

A large electrode is used

B welding rod coated with slag is used

C welding rod coated with fluxing material is used

D none of the above

Q43: In a hot chamber die casting machine

A ferrous alloys with low melting temperature are casted

B ferrous alloys with high melting temperature are casted

C non-ferrous alloys with low melting temperature are casted

D non-ferrous alloys with high melting temperature are casted

Q44: The type of file used for a wood work is

A single-cut file

B double cut file

C rasp-cut file

D any one of these

Q45: A zinc diffusion process is called

A galvanising

B anodising

C parkerising

D sherardizing

Q46: When a hole or cavity to be cored is not in line with the parting surface, then a __________ is used.

A horizontal core

B vertical core

C drop core

D balanced core

Q47: In a die casting method, the molten metal is forced into mould under high pressure.

A Correct

B Incorrect

Q48: Blanking and piercing operations can be performed simultaneously in a

A simple die

B progressive die

C compound die

D combination die

Q49: In a centrifugal casting method, the impurities are collected in the centre of the casting.

A Yes

B No

Q50: The temperature of oxy-hydrogen flame is __________ oxy-acetylene flame.

A same as

B less than

C more than

Q51: The centrifugal casting method, is used for casting articles of

A symmetrical shape about vertical axis

B symmetrical shape about horizontal axis

C irregular shape

D non-ferrous metal only


img not found
img

For help Students Orientation
Mcqs Questions

One stop destination for examination, preparation, recruitment, and more. Specially designed online test to solve all your preparation worries. Go wherever you want to and practice whenever you want, using the online test platform.